Perform a factory reset on firmware v2.6.6. Flash it with firmware v2.6.6. Load the radio with a v3.0.6 configuration file (this seemed to un-confuse the radio).
![]() Run this command in a terminal:References: single command global Application Security in MacOS 10.15+ (Catalina) ¶Unfortunately, Apple has made significant changes in 10.15 which cause major issues for independent software developers. run this command in the newly opened terminal window:Alternately, you can disable them for your entire system, although this has security implications that should not be ignored. (Don't see that menu item? Instructions to enable it) control click on the unzipped application and select New Terminal at Folder. The functionality is still there, but must be enabled from the command line.To whitelist a single application (like an unzipped chirp-daily.app): Then choose Allow apps downloaded from: Anywhere.Application Security in MacOS 10.12 - 10.14 ♪s of 10.12 (Sierra) the UI for disabling app security was removed. These cables are not all the same, so the computer needs a software "driver" so it can recognize the cable and speak to it correctly. Mac USB Drivers ¶USB to serial cables are not merely wire, they contain small computer circuits at one end of the cable that respond as a USB device and convert the data to serial. Please see issue #7147 for the current information about workarounds. Also note that there are significant limitations on what files unsigned applications can access which makes it very difficult to open, save, find, and otherwise organize image and CSV files with chirp. To Allow Programming Radio Mac OS X OnProlific PL-2303 cables - official drivers for the genuine Prolific cables ♯YI: your cable, if using Prolific chipset, is more likely to be using a counterfeit chip than an original.Login as guest/ guest & look in the Support section. YMMV.Version 1.5.1 is available for Mac OS X on 64 bit, 32 bit and PPC machines. You may need to remove the OEM FTDI driver and use only the Apple FTDI driver, or you may need to disable the Apple FTDI driver and install the OEM FTDI drivers. FTDI cables ¶Note that with Mac OSX 10.9 "Mavericks", Apple provides their own driver for FTDI chipset. Best youtube video editing software for macAlso some reports of success with Snow Leopard, Lion: ¶ RTSystems cables ¶ for OSX 10.9.x (aka Mavericks): ¶See RTSystemsCablesAndMavericks for OSX < 10.9.x: ¶ Silicon Labs CP210x USB to UART Bridge VCP Drivers (including Kenwood TH-D72) ¶Macintosh OSX driver for the Intel and PowerPC Platforms versions 10.4, 10.5, 10.6, 10.7, 10.8, and 10.9.The WinChipHead CH340 series chipset is not compatible with the Prolific 2303 drivers. For earlier versions of Mac OS X up to 10.5 Leopard. After downloading, you may need to control-right click, then open in order to bypass Mac Gatekeeper. ¶ For Lion (10.7.x), Mountain Lion (10.8.x), and Mavericks (10.9.x): ¶You can try this one, which install open source pl2303 driver and remove any other driver versions: At this web page you may need to right-click or control-click to link to get it to download. Generic PL-2303 cables (counterfeit and/or “Generic”) If you aren't sure what kind of inexpensive cable you have, try this one first. You will need to download from the radio to CHIRP first, before uploading anything to the radio. The exact procedure varies by radio. Some radios need to be put into a "clone" mode to transfer to PC, some radios may need to be configured to use the mic/speaker jacks for PC transfer instead of for the speaker/mic. The exact procedure varies by radio. In many cases you need to connect the cable to the radio first, then power the radio on, while holding down some buttons. A signed driver compatible with Yosemite is available from as the driver offered on the manufacturer's website (in Chinese) is not signed and requires allowing unsigned kernel extensions, which is a significant security risk on OS X. Do not try to upload to a radio directly from a tab that was not downloaded from that same radio. Then copy/paste from one tab to the other & upload back to the same radio that produced that tab. If you want to download from one radio and upload those settings to another radio, first download from each radio to a separate “tab” of CHIRP. If CHIRP won’t launch & won't run, you may have neglected to install the Python runtime. CHIRP will give you this opportunity each time you download from the radio. If you are using multiple USB cables, each will create a different “virtual port”, meaning that you will need to select the correct virtual port for your radio when connecting to your radio. Some people have reported success by using an older version of the Prolific driver, or a 3rd party driver. This can cause connection problems because the official Prolific driver will ignore the counterfeit chip. When the USB cable is connected and drivers correctly installed, the cable will show up in the USB section of the System Profiler.Another way to see that the driver is correctly installed is to open Terminal and type: ls /dev/cu*It will return a list of virtual serial ports including something similar to: /dev/cu.usbserial-A501XQ5I (suffix will vary)That will return a long list of kexts, including something similar to this at the bottom (most recently installed are listed last): 142 0 0xffffff7f81fc8000 0x8000 0x8000 com.FTDI.driver.FTDIUSBSerialDriver (2.2.18) <112 32 5 4 3 1>Look at the CHIRP log for clues. If your radio is not "Supported", you can try downloading the newest Daily Build to see if support was recently added.You can verify that the drivers are installed & working by connecting the USB cable to your Mac, then running “System Profiler”, or “System Information” (found in /Applications/Utilities ).
0 Comments
Leave a Reply. |
AuthorShawn ArchivesCategories |